当前位置：首页 > 技术资讯
基于MIC3203设计的HBLED驱动方案
发布时间:2014-12-26 阅读：次 [打印文章] [关闭窗口]- MIC3203降压恒流高亮度LED(HBLED)驱动器,输入电压从4.5V到42V,效率大于90%,LED的电流精度±5%,开关频率高达1.5MHz,主要用在建筑物,工业和环境照明,LED灯,指示器和紧急照明,街道照明以及12V照明系统.
High-Brightness LED Driver Controller with High-Side Current Sense
The MIC3203 is a hysteretic, step-down, constant-current, High-Brightness LED (HB LED) driver. It provides an ideal solution for interior/exterior lighting, architectural and ambient lighting, LED bulbs, and other general illumination applications.
The MIC3203 is well sui工字电感ted for lighting applications requiring a wide-input voltage range.
The hysteretic control gives good supply rejection and fast response during load transients and PWM dimming. The high-side current sensing and on-chip current-sense ampli电感器生产厂家fier delivers LED current with ±5% accuracy. An external high-side currentsense resistor is used to set the output current.
The MIC3203 offers a dedicated PWM input (DIM) which enables a wide range of pulsed dimming. A high-frequency switching operation up to 1.5MHz allows the use of smaller external components minimizing space and cost. The MIC3203 offers frequency dither feature for EMI control.
The MIC3203 operates over a junction temperature from −40℃ to +125℃ and is available in an 8-pin SOIC package.
MIC3203 主要特性:
• 4.5V to 42V input voltage range
• High efficiency (>90%)
• ±5% LED current accuracy
• MIC3203: Dither enabled for low EMI
• MIC3203-1: Dither disabled
• High-side current sense
• Dedicated dimming control input
• Hysteretic control (no compensation!)
• Up to 1.5MHz switching frequency
• Adjustable constant LED current
• Over-temperature protection
• −40℃ to +125℃ junction temperature range
MIC3203 应用:
• Architectural, industrial, and ambient lightin空心电感g
• LED bulbs
• Indicators and emergency lighting
• Street lighting
• Channel letters
• 12V lighting systems (MR-16 bulbs, under-cabinet lighting, garden/pathway lighting)
图1.MIC3203/MIC3203-1方框图
图2.MIC3203降压LED驱动器电路
MIC3203/MIC3203-1 评估板
This board enables the evaluation of the MIC3203/MIC3203-1 for 1A LED current. The board is optimized for ease of testing, with all the components on a single side. The device operates from a 4.5V to 42V input voltage range, and controls an external power MOSFET to drive high current LEDs. When the input voltage approaches and crosses UVLO threshold, the internal 5V VCC is regulated and the integrated MOSFET is turned on if EN pin and DIM pin are high.
The inductor current builds up linearly. When the CS pin voltage hits the VCS(MAX) with respect to VIN, the external MOSFET is turned off and the Schottky diode takes over and returns the current to VIN. Then the current through inductor and LEDs starts decreasing. When CS pin hits VCS(MIN), the external MOSFET is turned on and the cycle repeats.Since the control scheme does not need loop compensation, it makes for a very simp塑封电感le design and avoids problems of instability.
Requirements
This board needs a single bench power source adjustable over the input voltage of 4.5V < VIN < 42V that can provide at least 1A of current. The loads can either be active (electronic load) or passive (LEDs) with the ability to dissipate the maximum load power while keeping accessible surfaces ideally < 70℃.
图3.MIC3203/MIC3203-1 评估板电路图
MIC3203/MIC3203-1评估板材料清单(BOM):
在FPGA上实现H.264/AVC视频编码标准尽管H.264/AVC承诺将此已有视频编码标准具有更高的编码效率，它仍为系统架构师、DSP工程师和硬件设计人员带来了巨大的工程设计挑战。H.264/AVC 标准引入了自 1990 年推出 H.261
Intersil推出用于便携式电子设备的开关稳压器 美国加州、MILPITAS--- 2014年10月8日 —创新电源管理与精密模拟解决方案领先供应商Intersil公司今天宣布，其市场领先的升降压和升压开关稳压器产品系列ISL911xx新增五个成
快速反应智能安全监控系统的设计与实现摘 要： 设计了一套快速反应嵌入式智能安防监控系统，实现对运动目标的跟踪、定位,快速捕获人脸图像。利用模式识别与图像处理技术对人脸特征进行分析，提取其特征量并与人脸库中的特征量进行匹配，判断是否为非法
